What Does Erl Mean On A Pit Boss Smoker?

BackyardCookingWorld.com is reader supported. We may earn a small commission from purchases made through links on this site at no extra cost to you. This helps us to keep providing great free content for people to enjoy.
---------------------

As soon as an error code appears on the screen of your Pit Boss Smoker, you begin to worry that your smoker is broken just before the summer BBQ season.

With Pit Boss Smokers, the most common error code that you will see is the Erl Code.

Usually, this code, aligned with others, is a sign that there is a broken connection in the smoker or a temperature malfunction.

Luckily, both of these things can be fixed somewhat easily, so you’ll be back to grilling and smoking your BBQ meats in no time.

Keep reading to find out all about the Erl code, and how to fix the problem in your smoker.

Contents

What Does The Erl Code Mean?

If you notice a warning that says “Erl” shown on the screen of your Pit Boss control board, this usually often means that there is a problem with the temperature sensor that is built directly into the smoker.

If the temperature probe cannot establish a connection with the controller, and the controller draws the conclusion that it is unable to read the data from the probe, this is when the Erl error code will be shown.

Pit Boss grills and smokers come standard with temperature probes and sensors that are incorporated right into the chambers where the food is prepared.

Because it constantly monitors the temperature and sends a signal to the controller, the temperature probe is an absolute necessity for the operation of grills and smokers.

The controller uses the signal to determine whether or not additional pellets need to be fed into the cooking chamber to keep the temperature at the desired level.

The failure of the temperature probe to continue communicating with the controller, which resulted in the display of the error message, might have been caused by a broad number of other issues.

In the majority of situations, the problem can be fixed with little to no effort; however, if you are dealing with a broken internal temperature probe or a cable that is not correctly attached, fixing the issue can be a bit harder.

Fixing The Erl Code

When attempting to repair the Erl error code that is shown on your Pit Boss Grill or Smoker, there are a few different routes that you may follow.

The bulk of the time, error messages is produced by Pit Boss Grills because of a filthy temperature probe.

Over time, the temperature sensor will accumulate filth, ash, and dust to the point that oil and grime will begin to form around the sensor.

This is a completely normal thing to happen, especially if you use your Pit Boss regularly.

When you switch on your Pit Boss grill, it instantly starts adding wood pellets to the burn pot, where they are ready to be lit and form a fire.

Once the fire is started, you can begin cooking your food. The pellets are put on the grill constantly up until the point where the internal temperature reaches the necessary level for cooking.

Nevertheless, if the temperature probe cannot send temperature data from the cooking chamber to the controller, the smoker or grill will shut down and display this error number.

The first thing you should do to try and get rid of the Erl message is to clean the temperature probe.

It’s probable that to gain access to the control board, you’ll need to take apart the smoker first.

Check to see that the probe wire is attached to the control board correctly, and inspect the control board for any other sorts of damage that may have occurred.

If your device is still covered under warranty but the control board has been damaged, all you need to do is get in touch with Pit Boss to get a replacement to be sent to you so that you may continue using your device.

Even if the equipment you are using is not covered by a guarantee, you can still buy this part online, though at a pretty high cost.

How To Prevent The Erl Code?

If you want to prevent the Erl code from appearing, the only thing you can do on your end to prevent it is to perform maintenance, so make sure you don’t neglect your smoker.

If the temperature probe is maintained and cleaned consistently, there is less of a chance that it will get contaminated with ash and grease over time.

When doing routine maintenance on a system, it is not difficult to identify faulty connections and damage to components.

Although it is possible for you to obtain the Erl error code on your Pit Boss grill even though you have performed all of the recommended maintenance on your grill, some people who own Pit Boss grills may never see this error message.

Tips for Resolving Frequently Occurring Issues

You can try out the following troubleshooting tips to find out what’s causing your grill to show an Erl message.

In addition to the routine maintenance that must be performed to keep your Pit Boss gadget in a state that allows it to work properly, you should also follow these steps below whenever you can.

  • The smoker or grill should be turned off and left to cool down for a bit.
  • Disconnect the grill or smoker from the power source after moving it away from the outlet.
  • Investigate the space underneath the smoker or grill for any connections that do not appear to be properly fastened, paying special attention to the temperature probe.
  • Conduct a thorough inspection of the temperature probe to check that it is not damaged in any way and does not have an excessive accumulation of grease or ash.
  • To properly sterilize the temperature probe, you should use a solution of vinegar and water.
  • The cleaning of the cooking chamber, as well as the burning pod, is very important.
  • You should attempt to vacuum the whole smoker if you have access to a vacuum. This will help remove any debris that may be there.

Summary

When you see the Erl error message on your Pit Boss Smoker, it means that there is something wrong with the temperature sensor and prob in the device.

The easiest way to fix this is to clean any dirt or grime off of the probe.

If this does not fix the issue, then you should try contacting Pit Boss support who will help you find out what the issue is.

If you are still under warranty, then you may be able t get a replacement or extra parts for your smoker for free.

Leave a Comment

error: